Full TMV strip-down service
TMV Servicing Specialists arranges full strip-down thermostatic mixing valve servicing across the UK. The valve is taken apart, its cartridge and internals are descaled, tired seals and worn parts are replaced and the mixed temperature is set again from scratch. It is the deeper job for older valves that have drifted and no longer hold steady.
When a valve needs more than a routine check
Thermostatic mixing valve servicing comes in two depths. A routine visit checks readings and cleans the inlets. A full service goes inside the valve body. The thermostatic cartridge, the piston or shuttle that moves inside it, the inlet check valves and the O-rings that seal them all wear and scale with time, and once they do the valve starts to respond slowly, overshoot when someone runs another tap, or creep a little higher each month. Cleaning the strainers will not reach any of that.
A full service is the right choice when a valve has drifted noticeably since its last reading, takes a long time to settle, shows a stiff or sluggish response, or was fitted years ago and has never been opened. It also suits hard water areas such as London, the South East and the East of England, where scale on the cartridge builds faster than in soft water parts of Scotland, Wales and the North West. Owners of older terraced houses and conversions, where valves are often tucked into cramped cupboards, tend to find that a valve has gone untouched for a long time.
It is not always the answer. If the cartridge is cracked, the valve body is corroded or parts are no longer made, a strip-down cannot restore it and a repair with new parts or a replacement valve is the honest next step. If the valve is new and holding its setting, a routine service or test is enough. The engineer tells you which applies once the valve is open.
What a full service involves
Every valve model comes apart a little differently, but a full strip-down service generally covers these stages.
- Readings before dismantlingThe outlet and supply temperatures are recorded first, so there is a baseline to compare against once the valve has been rebuilt.
- Isolation and drain-downHot and cold supplies to the valve are isolated and the valve body relieved of pressure before it is opened.
- Removal of the cartridgeThe thermostatic cartridge or element assembly is withdrawn from the body and inspected for scale, cracking and wear on the moving parts.
- Descaling the internalsScale is removed from the cartridge, the valve body and the seating faces using a suitable descaler, then everything is rinsed through.
- New seals and worn partsO-rings and seals disturbed during dismantling are normally renewed. Check valves and other small parts are replaced where they are worn, subject to availability for that model.
- Strainers cleanedInlet strainers are cleaned or renewed while the valve is apart, as debris here is often part of why the valve drifted.
- Reassembly and recalibrationThe valve is rebuilt, supplies restored and the mixed temperature set to the agreed figure at the outlet, then allowed to settle and checked again.
- Fail-safe test and recordThe cold supply is isolated to prove the valve shuts down, and before and after readings are written up for the valve.
What to plan before a strip-down
-
Make and model if you have them
A photo of the valve, its badge or the old service sheet helps the engineer bring the right seal kits and cartridge information.
-
Time out of use
A strip-down takes longer than a routine check, and the outlet is out of use while the valve is apart. Plan around bathing or shower times in occupied buildings.
-
Working isolation valves
If the valve's own isolators have seized, wider isolation of the hot and cold supply may be needed, which can affect other outlets.
-
The agreed set point
Know what temperature each outlet should be set to, ideally from your risk assessment, so the valve is recalibrated to the right figure.
Good to know about full servicing
-
Parts depend on the model
Seal kits and cartridges are available for many common valves, but some older or discontinued models have no parts. In that case the engineer will say so and replacement becomes the realistic option.
-
A rebuilt valve still needs watching
After a strip-down, a valve behaves much like a newly commissioned one. Checking it again a few weeks later shows whether it is holding its new setting.
-
Scale is often the cause
In hard water areas, scale on the cartridge is the most common reason a valve drifts or sticks. Water treatment upstream can lengthen the time between strip-downs.
-
Not every valve can be opened safely
Valves seized into pipework or with corroded unions may need extra work just to get them apart. If that risks damage, the engineer will discuss it before going further.
How a full service is arranged
- 1
Describe the valve
Use the enquiry form to tell us where the valve is, what it serves and how it has been behaving. Photos help.
- 2
A partner engineer is chosen
Alex reviews the details and matches the work to a partner engineer covering your part of the UK.
- 3
The price is confirmed
Price depends on the valve, its access and the parts it is likely to need. We confirm it before work starts, and any extra parts found on the day are agreed with you first.
- 4
Strip-down and rebuild
The engineer dismantles, descales, renews seals, rebuilds and recalibrates the valve, then proves the fail-safe.
- 5
Your record
You should expect before and after readings, the fail-safe result and a note of parts fitted, plus any recommendation for the future.
Full service questions
How do I know if my valve needs a full service?
Signs include a reading that has moved several degrees, a slow or jumpy response when other taps run, or a valve that has never been opened since it was fitted.
Is a full service cheaper than replacing the valve?
Often, when parts are available and the body is sound. If the cartridge or body is beyond saving, the engineer will say so rather than rebuild a valve that will not last.
How long is the outlet out of use?
That depends on the model and access. Plan for the outlet to be unavailable for the length of the visit rather than a few minutes.
Do you replace the cartridge as standard?
No. The cartridge is descaled and reused if it is sound. A new cartridge is fitted only where it is worn or damaged, and that is agreed with you first.
Can a full service fix a valve that fails its fail-safe test?
Sometimes. Scale or debris can stop the cartridge shutting off, and cleaning it can restore the fail-safe. If the element itself has failed, a new cartridge or valve is needed.
Will the temperature be set the same as before?
It is set to the figure your site has agreed. If that is not recorded anywhere, the engineer will ask you to confirm it before recalibrating.
Should the valve be checked again afterwards?
It is good practice. A follow-up reading after a few weeks confirms the rebuilt valve is holding steady.
Other work on the same valves
- TMV servicingThe routine visit with readings, a fail-safe test and a light clean, for valves in good order.
- TMV repairReplacement cartridges, seal kits and check valves fitted when a strip-down finds worn parts.
- TMV replacementA new valve where the old one cannot be rebuilt or parts are no longer made.
- TMV commissioningSetting and recording a valve's baseline performance, as after installation or a major rebuild.
Ask for a full TMV service
Send an enquiry with the valve's location and how it has been behaving. Alex will pass it to a partner engineer and the price is confirmed before work starts.
Send an enquiry