Skip to content

TMV servicing across the UK

TMV servicing for leisure centres

TMV Servicing Specialists arranges TMV servicing for leisure centres and gyms across the UK. Shower blocks in sports halls, swimming pools and fitness clubs run for hours each day, and the thermostatic valves feeding them scale up and drift faster than those in most buildings. A partner engineer tests, cleans and resets them, then records what was found.

A thermostatic mixing valve fitted on clean copper pipework against a painted wall

Shower blocks that never get a rest

A changing room at a busy pool or gym might run a bank of showers from early morning to late evening, seven days a week. That steady demand pushes a lot of water through the strainers and cartridges, and in hard water areas the scale builds quickly. At the same time the users are a mix of everyone: school swimming groups, older people at aqua classes, disabled swimmers, parents with toddlers. A shower that suddenly runs hot can hurt someone who cannot step away quickly. This page is for leisure trust managers, council and contractor facilities teams, gym operators, golf and sports club committees and anyone else responsible for public showers.

Leisure buildings tend to use two kinds of valve. Some shower blocks are fed from one or more large blending valves in a plant room, which mix water for a whole run of showers. Others have a TMV at or near each shower or basin. Both need servicing, but the work differs: a blending valve serves many outlets, so testing means checking temperatures at the far ends of the run as well as at the valve, and a failure affects the whole room. Point-of-use valves are simpler individually but there are many of them. Long mixed-water runs from a central blending valve also need attention under the Legionella risk assessment, because warm water held in pipes suits bacterial growth.

This is the right page if you run a leisure centre, pool, gym, sports club or similar and want showers looked after on a planned basis. If you are considering swapping a central blending valve for valves at each shower, a TMV survey is a better starting point. For a single shower that has failed, TMV fault finding or TMV repair is quicker.

What a leisure centre TMV visit covers

The engineer works through the shower blocks, pool-side showers and plant room valves on your list. A visit usually includes:

  • Blending valve testingCentral blending valves are checked at the valve and at the showers they feed, including the furthest outlet, so you know temperatures hold across the whole run.
  • Point-of-use valve testingEach TMV on a shower or basin is tested for mixed temperature and fail-safe performance, with the reading recorded against a shower number.
  • Heavy descalingStrainers, cartridges and check valves are cleaned of the scale that builds up under constant use, especially in hard water regions such as London, the East of England and the Midlands.
  • Shower head and hose checksHeads and hoses that are heavily scaled or damaged are noted, since they affect flow and how well the valve controls temperature.
  • Pool-side rinse showersOpen showers on the pool hall wall are tested and checked, as they are used by bare-skinned swimmers and often overlooked.
  • Accessible changing roomsShowers and basins in accessible and family changing rooms are tested, and settings reviewed with your risk assessment in mind.
  • Records per shower and per valveReadings before and after, fail-safe results and a list of parts to replace, laid out so your duty manager can find any shower quickly.

Before booking leisure centre TMV work

  • Closing showers in turn

    Work out whether shower blocks can close one at a time during quieter sessions, or whether the visit should be early morning or after closing.

  • Plant room access

    Blending valves usually sit in plant rooms. Have keys, any permits to work and a member of staff who knows the plant available.

  • Know your valve layout

    A note of which blending valve feeds which changing room, or how many showers have their own TMV, helps the price and planning.

  • Check the written scheme

    Look at what your Legionella risk assessment says about blending valves, mixed-water pipe runs and flushing so the visit lines up with it.

Good to know for leisure operators

  • Heavy use means shorter intervals

    Valves that see constant flow and hard water often drift sooner. Intervals are set by drift measured at each test, so busy sites may end up with more frequent visits than quieter ones.

  • Closed areas need flushing

    Showers shut for repairs, refurbishment or a quieter season should be flushed regularly and before reopening, with the flushing recorded.

  • Central blending is a single point of failure

    If one blending valve fails, a whole changing room may go hot or cold at once. Some operators keep spare cartridges on site for that reason.

  • Point-of-use valves shorten warm pipe runs

    Moving from a central blending valve to valves at each shower reduces the length of mixed-water pipe, which HSG274 guidance favours. A survey can show whether it is practical.

How leisure centre TMV work is arranged

  1. 1

    Fill in the enquiry form

    Tell us the site, how many changing rooms and showers there are, and whether they run from blending valves or individual TMVs.

  2. 2

    Alex finds an engineer

    Alex matches the site to a partner engineer who can work around your opening hours and session timetable.

  3. 3

    A price before anything starts

    Pricing depends on the number of valves, plant room access and how much scale is found. We agree it with you first.

  4. 4

    On site

    Showers are closed in turn, valves cleaned, tested and reset, and each block reopened before the next is started.

  5. 5

    Paperwork afterwards

    You should expect readings per valve and shower, fail-safe results and a schedule of any repairs or replacements needed.

Leisure centre and gym TMV questions

See all questions

Is a blending valve the same as a TMV?

Both mix hot and cold water to a set temperature. A blending valve usually supplies several outlets from one point, while a TMV is fitted close to a single outlet.

Why do our showers keep going cold or fluctuating?

Scaled strainers and cartridges are the usual cause in heavily used showers. Cleaning and testing often restores control; worn cartridges may need replacing.

Can work be done while the centre is open?

Yes, usually by closing one changing room or a few showers at a time. Pool-side showers may need doing before opening or after closing.

How often should leisure centre showers be serviced?

Your Legionella risk assessment and written scheme set the interval. Busy sites in hard water areas often need more frequent visits because valves drift faster.

What temperature should public showers run at?

41°C is commonly used as the maximum at showers. Your risk assessment may set a lower figure.

Should we replace our central blending valve with individual TMVs?

It shortens warm pipe runs and means one failure only affects one shower, but it is a bigger job. A survey can set out the options.

Keep your showers running safely

Send an enquiry with your site and shower count, and Alex will match it to a partner engineer who can work around your timetable. The price is confirmed before work starts.

Send an enquiry